ORIENTAL MOTOR U.S.A. Corp.
570 Alaska Avenue
Torrance, CA 90503
1-800-GO-VEXTA (468-3982)
ORIENTAL MOTOR U.S.A. Corp.
570 Alaska Avenue
Torrance, CA 90503
1-800-GO-VEXTA (468-3982)
Product Line |
Oriental Motor® |
Frame Size |
1.65 in |
Motor Length |
2.68 in. |
Speed-Torque Characteristics |
 Speed - Torque Characteristics |
Holding Torque |
42 oz-in |
Type |
Continuous Duty |
Shaft/Gear Type |
Round Shaft (No Gearhead) |
Feedback Device (Motor) |
Resolver |
Shaft |
Double |
Electromagnetic Brake |
Not Equipped |
Power Supply |
Single-Phase 100-115 VAC |
Resolution (Resolution Setting: 1000 P/R) |
0.36 °/Pulse |
Rotor Inertia |
0.32 oz-in² |
Control Power Supply |
24 VDC ± 5%, 0.5A |
RoHS Compliant |
Yes |
Safety Standards |
UL CSA EN CE |
CE Marking |
Low Voltage Directives EMC Directives |
Components |
ARD-A [Driver] ARM46BC [Motor] |
Maximum Input Pulse Frequency |
When the host controller is a line driver output: 500 kHz (When pulse duty is 50%) When the host controller is an open-collector output: 250 kHz (When pulse duty is 50%)* *When driver cable CC36D1-1 is used. |
Control Command |
Pulse input |
Insulation Class |
[Motor] Class B [130ºC (266ºF)] |
Insulation Resistance (Motor) |
100 MΩ or more when 500 VDC megger is applied between the following places: Case - Motor and sensor windings |
Insulation Resistance (Driver) |
100 MΩ or more when 500 VDC megger is applied between the following places: PE terminal - Power supply terminal Signal I/O terminal - Power supply terminal |
Dielectric Strength (Motor) |
Sufficient to withstand the following for 1 minute: Case - Motor and sensor windings 1.5 kVAC 50 Hz or 60 Hz |
Dielectric Strength (Driver) |
Sufficient to withstand the following for 1 minute: PE terminal - Power supply terminal 1.5 kVAC 50 Hz or 60 Hz Signal I/O terminal - Power supply terminal 1.8 kVAC 50 Hz or 60 Hz |
Ambient Temperature (Motor) |
-10 ~ 50ºC (14 ~ 122º) (non-freezing) (when a heat sink of a capacity at least equivalent to an aluminum plate with a size of 9.84 x 9.84 in., 0.24 in. thick is installed.) |
Ambient Temperature (Driver) |
0 ~ 50ºC (32 ~ 122ºF) (non-freezing) (when a heat sink of a capacity at least equivalent to an aluminum plate with a size of 7.87 x 7.87 in., 0.08 in. thick is installed.) |
Ambient Humidity |
85% or less (Non-Condensing) |
Operating Atmosphere |
No corrosive gases, dust water or oil |
Degree of Protection |
[Motor] IP20 [Driver] IP20 |
Stop Position Accuracy |
±4 arc minutes (±0.067º) |
Shaft Runout |
0.05 mm (0.002 in.) T.I.R. |
Concentricity |
0.075 mm (0.003 in.) T.I.R. |
Perpendicularity |
0.075 mm (0.003 in.) T.I.R. |
Radial Load |
0 in. from Shaft End = 7.8 lb0.2 in. from Shaft End = 9.9 lb0.39 in. from Shaft End = 13 lb0.59 in. from Shaft End = 19.1 lb |
Axial Load |
3.3 lb |
Driver Type |
Pulse Input Type |
